Hose Storage

(1) Storage warehouse hose should be kept clean, ventilation, relative humidity below 80%, the temperature inside the warehouse should be kept between -15 ~ + 40 ° C, and avoid direct sunlight and rain and snow hose dip shower.
(2) when the hose storage, should be placed under the different varieties and specifications are not mixed stack, and to obtain access badges.
(3)hydraulic hose stored in a relaxed state as possible, generally less than 76mm inside diameter hoses coiled storage (but not less than the inner diameter of the disk 15 times the inside diameter of the hose)
(4) In order to prevent the hose storage tube compression deformation, stacking is not too high, generally stack height should not exceed 1.5m; and require the c during storage is often "down stack", generally at least once every quarter .
Heat from the outside and should be away from 1m; (5) the hose storage, not acid, alkali, oils and organic solvents or other corrosive liquids, gases in contact with
(6)hose fittings during storage, non-stacked tubular body weight and prevent outside squeezed and damaged.
(7) hose during storage generally should not exceed two years, and should be used before storage, first use, to prevent prolonged storage affect the quality of the hose.

Hose transportation

hydraulic hose during loading and unloading, should pay attention to the following points
hose fittings during loading and unloading, to do Handle gently.
Hose reel need Classification (article) neat shipment, to avoid excessive bending of the tube discounts, and should not be on the heap pressure hose other heavy objects.
Prohibited the hose with acids, alkalis, oils and organic solvents, flammable and explosive materials mixed; tube should not be in direct contact with the sharp edge of the cargo.
For straight transport hose required when length exceeds the load compartment, the long part should support bracket to prevent damage to the hose on the ground mop.
If for any reason need to hose temporarily parked in the open air (or workshop Pier), the site must be flat, flat hose should be neat, and do underlay cover, do not stack ballast; at the same time, the hose is not in contact with the heat source.
When transporting hose should not drag anywhere on the heavy hose lifting equipment should be used special equipment or handling and to prevent the hose from accidental damage.

Hydraulic working medium

Acting hydraulic machines used for working medium not only to pass the pressure, but also to ensure the machine working parts work is sensitive, reliable, long life and low leakage. Hydraulic basic requirements for working medium are: ① have appropriate liquidity and low compressibility in order to improve the efficiency of the transmission; ② can prevent corrosion; ③ good lubricating properties; ④ easy to seal; ⑤ stable performance, long-term work without deterioration. hydraulic machines with water as the working medium initially, after the switch in water by adding a small amount of emulsified oil emulsion made to increase lubricity and reduce corrosion. Late appeared to mineral oil as the working medium of the hydraulic machine of the 19th century. Oil has good lubricity, corrosion resistance and moderate viscosity, help to improve the performance of hydraulic machines. The second half of the 20th century there has been a new type of water-based emulsion, which emulsion form is "water in oil" instead of the original "oil in water." "Water in oil" emulsion external phase is oil, its lubricity and corrosion resistance close to the oil, and a small amount of oil, non-flammable. But the water-based emulsion expensive, limiting its promotion.

Hydraulic Works

hydraulic machines  used for working medium not only to pass the pressure, but also to ensure the machine working parts work is sensitive, reliable, long life and low leakage. Hydraulic basic requirements for working medium are: ① have appropriate liquidity and low compressibility in order to improve the efficiency of the transmission; ② can prevent corrosion; ③ good lubricating properties; ④ easy to seal; ⑤ stable performance, long-term work without deterioration. Hydraulic machine with water as the working medium initially, after the switch in water by adding a small amount of emulsified oil emulsion made to increase lubricity and reduce corrosion. Late appeared to mineral oil as the working medium of the hydraulic machine of the 19th century. Oil has good lubricity, corrosion resistance and moderate viscosity, help to improve the performance of hydraulic machines  The second half of the 20th century there has been a new type of water-based emulsion, which emulsion form is "water in oil" instead of the original "oil in water." "Water in oil" emulsion external phase is oil, its lubricity and corrosion resistance close to the oil, and a small amount of oil, non-flammable. But the water-based emulsion expensive,

hydraulic fittings manufacturers good news is

 This construction machinery industry, the most prominent contradictions finally attracted much attention, the huge market demand has finally push the industry forward fittings rolling wheels. October 11, 2010, bspt fittings the Ministry of Industry and Information Technology issued "basis machinery parts industry revitalization plan." Which clearly should be made to accelerate the pace of development of key components to break the bottleneck, we continue to meet the needs of the field equipment and the development of strategic emerging industries.British hydraulic fittings good news is, this construction machinery industry, metric tube fittings the most prominent contradictions finally attracted much attention, the huge market demand has finally push the industry forward fittings rolling wheels. October 11, 2010, the Ministry of Industry and Information Technology issued "basis machinery parts industry revitalization plan."