cutting machine maintenance Maintenance

1, the operation is complete studio and stage applications running water surface rock residue and wipe dry.

2, regular cleaning of the carriage and the rail and rail grease on the screw drive, and promptly filling oil.

3, all the work after the end of the blade moves forward 10 centimeters, making the trip switch rocker reset.

4, cutter machine after use if not used within a certain period of time, you should move the blade and fixture parts and machines of some rust coated lithium place butter

.

Edit this paragraph
Instructions for use

1, cutting hydraulic hose adapters machines installed, check the various parts of machine power rotation is flexible, all loose fasteners.

2, power on, press the host button, the blade rotation is consistent with the direction of the arrow. If the reverse immediately adjusted. After checking clamping rock samples can be cut

, Rock-like clamping should choose a reliable gripping points, to prevent the phenomenon of virtual folders and fake clip. Cutting process in order to avoid damage due to shifting of rock cutting tools and rock samples.

3, the clamping irregular rock, the available top-pressure clamping, clamping methods, see Book 1. Clamping step: first rock samples 8 flat on the table, and then the top

Pressure clamp 10 moves along the T-slot 3 inserted, selected and rock samples from the fixture, jig base locking screw and move the mandrel bolts 13, to select a reliable gripping points,

Then move the plunger locking nut 11, followed by rotating plunger until the plunger to top dead rock samples, and tighten the mandrel nut 12 to prevent loosening of mandrel in the cutting process

.

4, when cutting core samples, such as rocks larger quantities available random length plate attached to the pressure on the number of rock samples, together with the cutting, in order to improve work efficiency, clamping methods, such as

Figure 2 shows, the steps are as follows: The samples were eight flat on the table 6, the pressure plate bolts inserted along the T-slots 3, insert one end of a long table plate 9 square hole in the vertical plane,

Turn the adjusting screw 7 and the pressure plate bolts nut 10 can be pressed rock samples, such as the size of the core diameter slight error in the above plus a rock shaped like thin wood, so long

Plate can be pressed into the rock sample. Clamping and cutting a rectangular cube shaped rock sample, they apply this method.

5, the work, first start the main motor, and then work into the button to start cutting, because the rock with irregular shape, then feed slowly until the blade edge

All rock samples into only after a little faster.

6, cutters and retract automatically when the cutter along the table movement to the terminal, it can automatically back to Qiduan and automatically stops moving. If the work process requires

Back, click Control Panel rewind button. Needs to move forward and rewind, press the forward button can also work feed. Either feed or retraction, press the stop button to stop the cutter can be

Stop movement. Work, such as rock samples found far away from the cutter, press the fast-forward button (press and hold) or jog fast forward until the blade close to the rock sample, that is, release the button.

And then work into the button, the normal cutting. This can shorten feed auxiliary time. The machine feed drive as shown in Fig.

7, cutting the specimen, the hardness of the rock before work can be adjusted according to the feed rate during the cutting process to adjust the feed rate may be marks, according to

Experience cutting of hydraulic flanges hard stone, the speed is generally 40 mm / min or so.

Edit this paragraph
Cut-off

Suitable for cutting all kinds of special non-ferrous metals, aluminum, aluminum alloy, copper, copper alloy, plastic, plexiglass (acrylic) and carbon fiber and other materials. Especially for full self-

Aluminum cutting machine moving parts, heat sinks, audio panels, graphics cards, network cards, CPU, hard shells, MP3 aluminum, U disk aluminum ...... especially for these various materials

Short precision sawing electronic materials.

Introduction
1, by a programmable PLC program settings, automatic feeding, automatic folder feed, automatic sawing. Cycle of work for the automatic cycle. Cutting high precision, small vibration, low noise,

Simple operation, high efficiency, suitable for a lot longer sawing.

2, the floating feeding system, do not hurt the surface, a single feed stroke up to 650mm, continuous 3 times feeding, especially for short-material cutting.

3, the cooling system, so that the workpiece cut clean and accurate, no edges, increase blade life.